GSB-H5 horizontal high speed pump

Gsb-h SERIES PUMP IS a horizontal cantilever high speed pump, which is mainly composed of a motor, a growth box, a pump body, a lubrication system and a base. This series of pumps has the advantages of stable characteristic parameters, simple structure, convenient maintenance, high reliability, long service life and so on. Gsb-h3 /H5/H7 series high speed pumps are equipped with reflux stabilizer, which improves the characteristics of the pump in the small flow area and expands the flow regulation range of the pump. The High Speed shafting system is equipped with advanced bidirectional tilting tile bearings to ensure long-term stable operation of the pump under inlet pressure up to 10.0mpa.

Maximum flow: 110 m/h
Highest lift: 2500 m
Maximum suction pressure: 10.0 MPa
Temperature: -130 to 340 degrees Celsius

Features
Performance

Features

This series of pumps has the advantages of stable characteristic parameters, simple structure, convenient maintenance, high reliability, long service life and so on.

Specifications

Heads to 6,300 ft
Flows to 400 gpm
Standards API 610 OH6
Maximum Motor Power 200 HP
Temperature Range -200 to 650°F
Maximum Case Working Pressure 1,260 psi
Maximum Suction Pressure 1,000 psi
Differential Head 6,300 ft
Maximum Viscosity 750 cp
Solids Range 0.015″, 400 microns
Mounting Configuration Vertical, Horizontal
Seal Configurations Single, Double, Tandem
Inducer Yes
Flanges ANSI 600# RF, 900# RF Optional
Suction and Discharge 3″ x 2″
API Plans 11, 12, 13, 21, 23, 31, 32, 41, 52, 53, 54, 61, 62, J

Heads to 1,348 m
Flows to 73 m³/hr
Standards API 610
Maximum Motor Power 150 kW
Temperature Range -130 to 340°C
Maximum Case Working Pressure 155 kg/cm²
Maximum Suction Pressure 71 kg/cm²
Differential Head 1,921 m
Maximum Viscosity 750 cp
Solids Range 0.381mm, 400 microns
Mounting Configuration Vertical, Horizontal
Seal Configurations Single, Double, Tandem
Inducer Yes
Flanges ANSI 600# RF, 900# RF Optional
Suction and Discharge 3″ x 2″
API Plans 11, 12, 13, 21, 23, 31, 32, 41, 52, 53, 54, 61, 62, J

Materials

LMV 311 BUILD CODES	A	E	J	O (1)	W
API 610 BUILD (2)	S-5 (3)	A-7 (4)	S-8 (4)	N/A	S-9 (4)
Pump Case	C.S.	316 SS	C.S.	316 SS	Monel Clad C.S.
Case Studs	B-7	B-7	B-7	B-8M	K-Monel
Seal Housing	C.S.	316 SS	C.S.	316 SS	Monel
Separator	316 SS	316 SS	316 SS	316 SS	Monel
Diffuser Insert	C.S.	316 SS	316 SS	316 SS	Monel
Diffuser Cover	C.S.	316 SS	316 SS	316 SS	Monel
Impeller	316 SS	316 SS	316 SS	316 SS	Monel
Impeller Bolt	316 SS	316 SS	316 SS	316 SS	K-Monel
Inducer	316 SS	316 SS	316 SS	316 SS	Monel
Tab Washer	316 SS	316 SS	316 SS	316 SS	Monel
Shaft Sleeve	316 SS	316 SS	316 SS	17-4 PH	Monel
Throttle Bushing	316 SS	316 SS	316 SS	316 SS	Monel
Metal Seal Parts	316 SS	316 SS	316 SS	316 SS	Monel
Stationary Face	Binderless Carbon or Silicon Carbide
Rotating Face	Tungsten Carbide with Cobalt or Nickel Binder
Shaft (all)	4140 Steel to 0° F, 15-5PH from 0° F to –240° F.
O-rings	As Required

“O” build temperature range 0° to -240° F. Pressure capability is reduced due to strain hardened pump case studs. Contact Application Engineering.
See handsome Corporation exceptions/clarifications to API 610, 11th edition for material requirements of pump parts.
Impeller is upgraded to 316SS. A seal gland is not required because the seals mount in the seal housing. O-rings are used instead of a case gasket.
A seal gland is not required because the seals mount in the seal housing. The pump shaft is AISI 4140 because it is not exposed to the fluid. O-rings are used instead of a case gasket.